HMS Hood 1/200 Amati Models

[Bigfoot57]

HMS Hood 1/200 Hachette /Amati Wooden kit Build Part 72-74 More deck details and finally the next decking layer

Hello again sorry for the sporadic nature of my updates work has dictated this at present anyway here’s where I’m at
So we add some deck detail including what look like lifeboat davits to me along with the 2 side panels built back in issue 47 I think
Next they tell you to add the 5 separate deck pieces to the top of all those upright supports previously installed now if you do it the instruction way you’ll be left with gaps to fill in the uneven joints
So I’ve joined all the pieces together beforehand and strengthened them with thin card strips on the rear which will effectively become the ceiling o n top of the supporting structure this I have 5 good flat perfect no gap joins and the deck just rests on top of the supports with minimum of adjusting required it will be glued into position prior to stage 76 taking place
As always please see attached photos of instructions followed by my actual build

Regards

Colin

[Bigfoot57]

HMS Hood 1/200 Hachette /Amati Wooden kit Build Part 75 next decking layer

So here is the very minor part of issue 75 ie 5 pieces of thin wood and a small brass detail that has to be saved for later
As you can see as mentioned previously I’ve glued all the deck panels together to make one homogenous flat & even piece of decking instead of 5 individuals which I think looked terrible

Regards

Colin

[Bigfoot57]

HMS Hood 1/200 Hachette /Amati Wooden kit Build Part 76-77 Fitting next decking layer Sanding 78

So again not much to do in these 2 sections basically glue the deck pieces to the supports and then build some more hose reels and mountings and finally sand the hull down fill any imperfections re sand and repeat as necessary ready for the primer coat

Regards

Colin

[Bigfoot57]

HMS Hood 1/200 Hachette /Amati Wooden kit Build Part 78-79 Sanding & Filling
Hello
So did my 1st primer coat on the hull and all those lighter patches are where filler has been added this will all need sanding smooth and the whole process repeated until we have a completely smooth surface
I also finished of the hose reels that will be mounted onto the main decks

Regards

Colin

[Jim R]

Hi Colin
She's looking good and huge. Lots of different materials and techniques on this. Filling and sanding the hull will be time consuming but worth it to get a perfectly smooth finish.
Jim

[Bigfoot57]

HMS Hood 1/200 Hachette /Amati Wooden kit Build Parts 80 to 82 Fitting the centex decking onto the ship

Hello again with the continuing build of HMS Hood this time were adding the Centex deck areas I believe that’s what they are called as it was a special non slip type of surface and was a dark grey from the look of it according to Amati anyway that’s the colour I have used
After this test fitted & any areas that weren’t level were shimmed up to bring them level using thin card on the tops of the structure below before gluing down using pva glue this was were the joins were as this decking was in 6 parts
I also added card bracing along the joins on the underneath to give it more stability so as usual here’s the mags photos followed by my own

[Bigfoot57]

Now here are my build photos for this section

[ATTACH alt="41D2D01E-C1EF-46CB-ACDF-D165C67D90F1.jpeg"]450706[/ATTACH]

[Jim R]

Hi Greg
There's a lot in that stage. Adding shims and strengtheners is extra work but well worth doing. Looking very good.
Jim

[Bigfoot57]

HMS Hood 1/200 Hachette /Amati Wooden kit Build Parts 83 to 85 Adding bulkhead walls to the Centex decking

In this section we are adding bulkhead walls to the Centex decking this involved fitting dozens of tiny buttressing pieces on to the bulkheads before bending them into the correct shapes then adding them to the decking as shown
The hull is also now ready for whatever comes next it is smooth and contoured I would think it would be its 1st proper colour but we still got the the exterior details to be added such as the propeller mountings etc

So here’s the mags my build photos will follow as normal

[Bigfoot57]

Here’s my build photos

[scottie3158]

Colin,
Cracking work mate keep it up.

[Bigfoot57]

HMS Hood 1/200 Hachette /Amati Wooden kit Build Parts 86-87 Motor launches

Yep this time were building 5 Motor Launches 3 x25ft & 2x 40ft these were incredibly fiddlesome to build and the end result is far from perfect but it’s the best I’m able to achieve so I’ll live with it

Next set are my builds for this section

[Bigfoot57]

Build Photos Parts 86 & 87

[adt70hk]

Colin,

Apologies for behind on this. That's coming on beautifully. Great work all round and at 1/200 if have no complaints about your motor launches.

Keep up the great work.

Andrew

[Jim R]

Hi Colin
Nothing wrong at all with those motor launches.
Jim