System Light Dark

Theme editor

Page Setup Appearance

  • Page Width

    Toggle Page Width

    Allows you to change page width values

    Color Pickers

    Toggle color picker

    Allows you to change the color of some predefined items

    Typography

    Select the font you want to use

  • Styles

    Select the style you want to use

    Style variation

    Select the style variation you want to use
    System Light Dark
Scale Model Shop

"Pete's Toon Factory" The End

  • Thread starter Thread starter Guest
  • Start date Start date
Status
Not open for further replies.
Thread owner
No bench work for the next 2 days off to RAF Duxford Daks over Normandy tomorrow and on the 6th down to Portsmouth for the D-Day celebrations.
Hopefully we'll have a lot of pictures.
Pete
 
Thread owner
Pete Low said:
Hi got a bit more done on the Toon Panther Ostwallturm.


I used a coat of Liquitex to represent concrete.


Added air shaft vent.


Primed base and turret.




Painted concrete a light grey and red oxide for the steel turret plate ring.






The inside of just one type of these Panther Ostwallturm.



Thank you for looking in.
Pete.
Click to expand...
Pete. Did the crew have to pump the air like in my" Dusty Bin " I did a few years back ?
Wolverine one coming on well .:thumb2:
 
Thread owner
John Race said:
Pete. Did the crew have to pump the air like in my" Dusty Bin " I did a few years back ?
Wolverine one coming on well .:thumb2:
Click to expand...
Hi John this might answer your question.

The concrete sub-structure was a standard construction (Regelbau 687) built by the Organisation Todt (OT). It required some 175 m3 of concrete and approximately 10 tons of steel to reinforce the structure. When finished the bunker was slightly higher than the surrounding ground. This was to enable the construction of an angled apron of concrete, which was designed to prevent enemy fire from penetrating the bunker and to prevent blast damage to the loose soil around the turret when the gun fired.
The bunker itself had three rooms. The room directly below the turret housed a motor that operated the hydraulic rotation mechanism in the turret. Using this the turret could be traversed at six degrees per second. The motor also powered a compressor, which provided compressed air to flush out the barrel. Behind this room was an ammunition storage room which was capable of storing 450 rounds of 75 mm ammunition. The room below the turret that housed the motor was linked by several wooden steps to an ante-room. This was home to a generator and a battery which provided power for lighting, to operate the turret fan and for the electrical discharge. It also doubled as the crews living quarters and was fitted with a stove, but no beds. The smoke from the stove, together with the exhaust from the motor, was vented outside by means of a chimney. A door linked this room to a staggered entrance at the rear of the installation that led to a communication trench.
Pete.
 
Thread owner
Hi added some ID marking to bunker base, added turret base colour.



Made trans bolt strip, cut slot and fitted for the "Wolverine".


Removed rear engine doors, added exhaust pipes, tow bracket and hex nuts/ washer to the ends of idler axles.


Not much today sorry about that.
Pete.
 
Pete - the Matilda looks much better without the golf tee

Wasn't sure if that 'bunker' was real or just someone messing about with Photoshop again, but it appears to be real, the Lebanon Peace Monument. There is also one full of cars.

Looks like a T55 on the bottom with an Israeli M50 above it and possibly a Saladin A/C above that

Just looked it up on wiki and apparently there are 78 tanks/armoured cars in there along with 5000tons of concrete - would certainly make a very different model
 
Thread owner
Pete,
As always, they hit the mark, well done.
Cheers, Mike.
 
Pete,
You never disappoint great work on the panther turret and the ground work for the Sherman looks spot on.
 
Status
Not open for further replies.

Legal Notice

scalemodelling.co.uk is a privately operated online discussion forum. All content posted by members reflects their own views and opinions and does not necessarily represent those of the forum owners or administrators. While reasonable efforts are made to moderate content, no responsibility is accepted for user-generated material. By using this site, you agree to comply with UK law and the forum rules.

Currently on our website
Members online
Threads 36,188
Messages 695,637
Members 2,509
Latest member Cusack77
Back
Top