Search results
-
The HobbyBoss 1/32 B24D Liberator.
Model completed. One quick pic and I will load a completed model thread.- BarryW
- Post #159
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
Almost there … Only the front greenhouse to position with the guns inside. A bit of a delay though as I found that my non-fogging c.a. has dried up! At this time of year I cannot quickly get a replacement which means I need to use pva glue that has no ‘bite’ and takes time to dry. It won’t...- BarryW
- Post #153
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
Plenty of progress and now on the home run. I applied a Flory surge wash overall to bring out the panel lines and to tone down the clean paint look and followed up with matt coats. After the matt coat I got on with more weathering. Exhaust wash on the exhausts and airbrushed some exhaust...- BarryW
- Post #151
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
I have applied the decals but it did not go as planned. Originally I wanted to do the ‘Squaw’ markings from Kits World however, for the first time ever, Kits World let me down. First the roundels were beautifully thin but they curled at the edges and I had a hell of a job to ‘uncurl’ them. In...- BarryW
- Post #148
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
I have got in with some detail painting. After masking up I sprayed the wing, tail and stab leading edges with steel. Also I sprayed the exhausts with Pale Burnt Metal then shaded them with Burnt Iron. These need some more work with washes and pigments. That will need to wait a bit...- BarryW
- Post #146
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
All masked up ready to paint the sand. To paint this requires more contortions than I have ever tried before. First I did areas best acceded froM below Then I turn it over…. And finished. For the first time since using MRP I did get some splatter toward the end of the session...- BarryW
- Post #143
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
I have painted the Neutral Grey. As usual with something big, its best to work in small stages. Got there is the end. I managed all this on just one of the large cups of paint! Tomorrow there will be a lot of masking before doing the sand colour.- BarryW
- Post #139
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
Well everyone. This beautiful lady is now dressed up in her finest black lingerie ready to spray the underside Neutral Grey. I was right, there was a lot of seam work needed after the first black primer but now we are ready to proceed. This model is certainly taking a lot of spraying!!!- BarryW
- Post #133
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
A picture of the underside ready for paint. Sometimes, when spraying this one, I just have to accept that there will be overspray ‘escape’. Once finish I will go over everywhere with ipa to get rid of as much overspray as I can. The 1/32 Lancaster will seem small after this one.- BarryW
- Post #131
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
Well this shot of the airframe in front of my spray booth is another illustration of its size. This is my first use of the large 15ml spray cup with the Colani. The usual larger spray cups I had, the standard size are 5ml. Two full cups and the top of the airframe has been sprayed. I...- BarryW
- Post #129
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
I have been getting on with those sub-assemblies, weathering and detailing. With the engines I used steel effect Uschi Metal Powders. Having matted the black painted engine I rubbed the metal powder into the centre boss of the engine with a cotton bud to give it an oily steel look. I then...- BarryW
- Post #127
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
I had some back trouble so I was not at the bench for a week. However, the wings are on and seams sanded but my main progress has been on the remaining sub assemblies, engines, main landing gear and so on. There is still a fair bit of work to do on these, see the picture, when done I will be...- BarryW
- Post #124
- Forum: Aeroplanes Under Construction
-
1/32 Aircraft recommendations
Wow, that’s a big question. I have built well over 70 1/32 aircraft over the last 12 years or so. What is right for you very much depends on what you want. The 1/32 Tamiya Tomcat is an old kit that is not up to their later kits. I have not built it myself, choosing instead, the Trumpeter...- BarryW
- Post #2
- Forum: General Modelling chat
-
The HobbyBoss 1/32 B24D Liberator.
One final photo for today. Tops of wing are on….- BarryW
- Post #121
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
Only now, having fitted the lower wing section, can the sheer size of this model be appreciated with its 42 inch wingspan. It will look bigger still once the elevators, ailerons and top wing are fitted. I will let the cement fully cure before fitting the rest of the wings sections. I have to...- BarryW
- Post #116
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
I have made a start on the wings, constructing the wheel wells. Before gluing them into the lower wings I sprayed them with the new airbrush, plus the wheel well edges on the wing itself. The wheel wells are nicely detailed but I will have more work to do on them. Other wing parts waiting...- BarryW
- Post #114
- Forum: Aeroplanes Under Construction
-
Harder & Steinbeck Colani Airbrush review.
First a bit of background. I have used several brands of airbrush over the years, a cheap Chinese knock-off, Harder & Steinbeck Evolution and Infinity, GSI Creos PS275, Topnotch and Iwata. Of all of them, I like the H&S brushes most due to their very easy breakdown and easy clean up. They...- BarryW
- Thread
- Replies: 23
- Forum: Product Reviews
-
The HobbyBoss 1/32 B24D Liberator.
I have put together the tail. Fit was good though with tight tolerances. It fits perfectly to the tail with a click. I cemented it into place but leaving the end unglued to provide a bit of spring when fitting the rear turret into place. I have started work on the wings, more on that...- BarryW
- Post #111
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
I have finished the seams, at least for now. I will have to return to them when I have done the primer as there are bound to be flaws to treat. On to scribing. This is a skill that I do not claim to have mastered but it must be done. Below are the tools I utilise The main scribers are...- BarryW
- Post #108
- Forum: Aeroplanes Under Construction
-
The HobbyBoss 1/32 B24D Liberator.
This morning I went over her with a 400 grit sanding sponge. I was carefully checking for any ‘protuberances’ and eliminating them. Each time I now go over this the amount of material removed will be less, it will be 600 grade next. I then went over the seams looking for ‘dents’ or...- BarryW
- Post #107
- Forum: Aeroplanes Under Construction
Legal Notice
scalemodelling.co.uk is a privately operated online discussion forum. All content posted by members reflects their own views and opinions and does not necessarily represent those of the forum owners or administrators. While reasonable efforts are made to moderate content, no responsibility is accepted for user-generated material. By using this site, you agree to comply with UK law and the forum rules.