discussion Boatmans Super Hornet F18/A- F Build

[Waspie]

That's quite a big gap to deal with Chris. Gonna take a whole load of file, dry fit, file dry fit and repeat. Get Jen to make a big pot of tea and open a big packet of biscuits. You'll be at it a while

Agree - lots of tea!!!!
Bummer Chris. I think you need a harsher whip to tame that beast!!

 

[boatman]

Hi Chris,

Sorry mate missed this but here now. looking good so far.

HI Scottie you havnt missed much as i only posted this this afternoon but nice to see you havin a look as soon as i get all the led's in then i'll start the build an paint scyme proberly
cheers sir
chrisb

 

[boatman]

That's quite a big gap to deal with Chris. Gonna take a whole load of file, dry fit, file dry fit and repeat. Get Jen to make a big pot of tea and open a big packet of biscuits. You'll be at it a while

AN HI Jim yes that gap im use to them from my tomcat build lol but yes its goin to take a lot of work to get a good fit boy oh boy why is it me that get the bad fit kits lol an yes i take your tip Jim an a big cuppa an biccies from jen only hope the rest of the kit fits better oh dear but like the tomcat this will get built an lit up or my names not BOATMAN LOL
chrisb an jen

 

[boatman]

Agree - lots of tea!!!!
Bummer Chris. I think you need a harsher whip to tame that beast!!

AN HELLO Doug yes it is a bummer but i'll tame it as this is a smaller kit than that tomcat but i shew it who was boss dint i lol an this WILL GET BUILT THANKS BOTH for lookin in on this build cheers an its nice to be back in the grove as i dint think i would be able to master this new forum but ive just been sayin to myself well its a bit like the old one so stick at it an so far i have
ATB
chrisb an jen

 

[boatman]

HI ALL again just want to upload a pic from yesterday that failed to upload an its a shot of the front landing gear with the white landing light fitted as thought this light was goin to be a problem as when i first treid it it wont go but afterwards found out that the led manufacture had not stripped the negative wire so done that after some hassle as that plastic coatin is very strong an now the light goes thank god phew an the white 2mm led is fitted in a proper silver reflector what came with the kit an it was just made to order chrisb

 

[boatman]

That's quite a big gap to deal with Chris. Gonna take a whole load of file, dry fit, file dry fit and repeat. Get Jen to make a big pot of tea and open a big packet of biscuits. You'll be at it a while

HI Jim yes you was right regards that 4 mm gap in the front undercart bay but ive managed to get over the prob by gently cuttin down the front an rear side of the bay an the gently leaverin the side bit where the gap is up to the fusalarge side an glueining it an it worked fine so no more 4mm gap thank good ness
cheers to you sir for takin an intrest i the build
ATB
chrisb

 

[boatman]

HI ALL well the hornet build is still ongoin as its very complex how im building it with openin panels an lights an todayits taken me nearly all day just to get the outer red lines on the upper fusealarge as there is no defineing line to stick the tamyia maskin tape to must have taken that tape on an off several times as when i looked at it from top veiw it just did not look right but now i think ive cracked it an here a shot of the main maskin tape line

 

[boatman]

AN here fully masked up to be ready to spray on that nice insignia red

 

[boatman]

an sprayed red just got to hope there are no leeks underneath the tamyia tape an i sprayed this 3 times gently to get good coverage an to aviod runs in the paint phewnow goin to leave it for a day or so for the paint to harden

 

[boatman]

an while i was gettin the paint sorted ive been now near a week tryin to get the office intrument vid screens lights all wired up an as they are so thin like human hair an fragile ive finally done them an managed to solder all 12 wires an connect them up to a mini plug so it can just be plugged into the rear part of the fusalage an pic of the plug an these pugs have 3 pins on them as one pin is set further apart so its impossible to fit them in the wrong postion

 

[Jim R]

Always enjoy your updates Chris. Nice looking red paint job. It's the electrics and wiring that really amazes me - superb work.

 

[Guest]

Hi Chris.

Red and white painting I hate doing, but yours looks good. A tip I always spray a Matt varnish or primer on the area and once dried I then paint the colour, this seals the tape line so I don’t get any paint bleed.

 

[boatman]

an now that all the 2mm leds lights are all fitted i can begin to assess the layout of how the mini eletric plugs will befitted in the fusealage as got think ahead if i fit the plug in a certain postion will it allow the fusealge to jion up so really im at times spendin as much time thinkin ahead as im building an here a shot of the lower front part of the fusealarge an there is x 4- 2mm leds fitted in to it an ive been testin them like crazy as had one led pack up in one of the side avionnics bay but it was ok in the end just a bad connection phew an i'll say this hornet build is more difficult than the big tomcat phew again

 

[boatman]

AN couple of pics of the finished office with the led's all fitted in an its now ready to fit in the fusealage when that red paint is dry an maskin tape took off an if an red bleeds the i'll have to mask up the red an respray the grey phew an it took ages to solder all 12 wires that feed these tiny led's as the tiny wires are so springy an wont stay where i want them too Aaaaaccchhhhh was sweatin buckects an shakes but got them done without jens help as she is not to well as she is very depressed so i let her sleep on the seatee but she seems better now

 

[boatman]

cockpit shot from rear

 

[BattleshipBob]

Lovely office chris!!

 

[boatman]

Always enjoy your updates Chris. Nice looking red paint job. It's the electrics and wiring that really amazes me - superb work.

THANKS Jim CHEERS SIR yes i love me ole eletrics when they go right lol an cheers for your nice comments on the red paint work lets just hope it all comes out ok be glad when i can remove the maskin tape just got to keep fingers crossed as i will have to get some low tack maskin tape then i wont have to worry about pullin the paint off
ATB SIR chrisb

 

[boatman]

Hi Chris.

Red and white painting I hate doing, but yours looks good. A tip I always spray a Matt varnish or primer on the area and once dried I then paint the colour, this seals the tape line so I don’t get any paint bleed.

HI Dave cheers sir fot that info as ive never hardly needed to do this as that tamyia tape is very good an stops bleeds but always a first time isnt there are you goin to post more pics of your belfast on here as to me that looks to be a crackin build sir hope you do
ATB SIR
chrisb

 

[boatman]

Lovely office chris!!

THANKS Bob matey an you not fit on a avatar yet
chrisb

 

[Steven000]

Always amazes me how much electrical work you put in your models Chris! Dispite all the thin wires you managed to hook it all up, well done...

Take care of Jen, hope she's feeling better soon, a lot of people get a bit depressed when the leaves are falling from the trees. Hope you can cheer her up a bit...