discussion HMS Supply

[Guest]

Finally finnished putting on the veneer and it's turned out pretty well i think and just in the process of sanding the hull down now and i like the look of the different shades of walnut just hope it looks as good when iv'e given it a few coats of Danish Oil.

View attachment 57016View attachment 57017View attachment 57018View attachment 57019View attachment 57020View attachment 57021

View attachment 58993

View attachment 58994

View attachment 58995

View attachment 58996

View attachment 58997

View attachment 58998

View attachment 172019

View attachment 172020

View attachment 172021

View attachment 172022

View attachment 172023

View attachment 172024

 

[Guest]

ok iv'e given her a couple of coats of Danish Oil and polished the hull up and its turned out ok

View attachment 57136View attachment 57137View attachment 57138View attachment 57139

the next thing i did was to cut some more stanchions to the size given in the manual and they are a little bit bigger than the one's on the frames but i will need to cover them anyway to match the new one's

View attachment 57140View attachment 57141View attachment 57142View attachment 57143View attachment 57144View attachment 57145

Knife slipped as well when leveling off the rails so got to replace those bits again before capping the rails but these things happen

cheers steve

View attachment 59106

View attachment 59107

View attachment 59108

View attachment 59109

View attachment 59110

View attachment 59111

View attachment 59112

View attachment 59113

View attachment 59114

View attachment 59115

View attachment 172132

View attachment 172133

View attachment 172134

View attachment 172135

View attachment 172136

View attachment 172137

View attachment 172138

View attachment 172139

View attachment 172140

View attachment 172141

 

[flyjoe180]

Wow, the oil has made a huge difference. Great progress Steve, I don't comment much in the ship section but I am watching with interest.

 

[Guest]

Wow, the oil has made a huge difference. Great progress Steve, I don't comment much in the ship section but I am watching with interest.

Thanks for the comment and yes it has made a big difference and very pleased with the outcome the oil has brought out the natural colours in the wood better than i expected tbh

cheers steve

 

[Guest]

As im finding out with this kit some of the things are just not right ie the cast fittings supplied, in the manual the photos show these fittings as wooden so i can only presume this was a cost cutting exercise but to me they just dont look right at all and im going to have a go at scratch building some of them if i can, also i have found that some of the measurments are wrong like the bulwark stanchions are 5mm at the top together with a 2mm plank when i went to school that made 7mm width for the rail caps and what have they given me 5mm so had to go out and by some more wood for the caps and while i was at it got a sheet of mahogany to help me with some of the other things im thinking of redoing, but hey look on the bright side im learning new skills so its got to be worth it dont you think ?

cheers steve

 

[Guest]

Looking good Steve.

Andy

 

[Guest]

thanks Andy following your thread with great interest as well and looking very nice

steve

 

[Guest]

Steve thats a first rate planking and the colours awesome

mobear

 

[Guest]

thanks ole,the last couple of days been busy adding a couple of coats of paint using yellow ocre and black paint for the wales to the sides before capping the rails

View attachment 57371View attachment 57372View attachment 57373View attachment 57374View attachment 57375View attachment 57376View attachment 57377

i have also decided to have a go at scratch building a few of the fittings as i think they would look better than the cast metal ones supplied and those i cant do i will get online as my local model shop does not sell scale boat stuff

View attachment 57378View attachment 57379View attachment 57380the gun carrage should not be a problem but i think the grattings may well prove to be a problem but will give it a go first because the cast ones are not very good at all.

View attachment 59326

View attachment 59327

View attachment 59328

View attachment 59329

View attachment 59330

View attachment 59331

View attachment 59332

View attachment 59333

View attachment 59334

View attachment 59335

View attachment 172352

View attachment 172353

View attachment 172354

View attachment 172355

View attachment 172356

View attachment 172357

View attachment 172358

View attachment 172359

View attachment 172360

View attachment 172361

 

[Guest]

looking real nice just take your time with scratch build stuff,otherwise you go mad lol

mobear

 

[Guest]

Coming along great Steve. Now for some detail eh. Keep up the good work mate.

Andy

 

[Guest]

understand what your saying their ole iv'e just spent the best part of 2hrs trying to make a grating with a 2mm gap between each piece but they just kept breaking in my fingers, i dont have a vice or any fancy tools just my knifes and files and a modelling saw and my rotary tool so things are going to be a bit harder for me still thats the fun part. Anyway iv'e had a go at making a capstan and also the pre cast lifeboat that came with the kit i have planked it and will give it a coat of paint i think that will improve the look of it and save me having to buy a new one.

View attachment 57385View attachment 57386View attachment 57387View attachment 57388View attachment 57389View attachment 57390for this i used a piece of dowel used some of the spare mahogany planking i had left cut down for the strips on the lower half and i topped off with some walnut veneer strips sanded it then i have given it a coat of danish oil a couple more coats of that should harden it all up and improve the look.

View attachment 57391View attachment 57392View attachment 57393 i think when this is painted it will look ok.

iv'e also had another look at the fittings and noticed that the belaying pins were plastic so i have gone and ordered some wooden ones and some wooden gratings while i was at it

View attachment 59340

View attachment 59341

View attachment 59342

View attachment 59343

View attachment 59344

View attachment 59345

View attachment 59346

View attachment 59347

View attachment 59348

View attachment 172366

View attachment 172367

View attachment 172368

View attachment 172369

View attachment 172370

View attachment 172371

View attachment 172372

View attachment 172373

View attachment 172374

 

[Guest]

very very nicely done mate,love the capstan,keep this up and you should make a decent ship wainwright lol

mobear

 

[Guest]

Beginning to take shape now Steve - great work. Derek

 

[Guest]

Dedicated attention to detail

 

[Guest]

Thank you all for the kind comments, just had the dreaded phone call and off again on sunday upto lerwick so i wont be doing much more in the next couple of days but should get one more lot of pics up before i go.

steve

 

[Guest]

Been busy last couple of days and got a few more things done

View attachment 57490View attachment 57491View attachment 57492View attachment 57493View attachment 57494View attachment 57495View attachment 57496now the hull planking is finnished things should move along until i have to start running the rigging, then the fun will really start as iv'e never done that before so that will be another new skill.

cheers steve

View attachment 59437

View attachment 59438

View attachment 59439

View attachment 59440

View attachment 59441

View attachment 59442

View attachment 59443

View attachment 172463

View attachment 172464

View attachment 172465

View attachment 172466

View attachment 172467

View attachment 172468

View attachment 172469

 

[Guest]

still waiting on a few bits from cmb which should arrive any day now but wont be using them till next trip so no panic,last day today working on the ship so i was up early and been hard at it.Got to the stage where i was supposed to put the bits on but i did'nt fancy using those as they are just black plastic and the pics in the instruction book shows wooden ones so knuckled down and made my own which was a little tricky as they are only 3x3x6mm and i think look more to scale than the plastic ones supplied.

View attachment 57497View attachment 57498View attachment 57499View attachment 57500View attachment 57501View attachment 57502View attachment 57503 i have also started adding some of the decorative pieces but used my own colour scheme for them and im painting them all gold rather than the white suggested and i think look better and since im building this to please me im just going to go with what i prefer a bit of artistic license shall we say

View attachment 57504View attachment 57505View attachment 57506View attachment 57507View attachment 57508 and finally i have assembled the rudder and tiller arm, another fiddley job

View attachment 57509View attachment 57510View attachment 57511View attachment 57512View attachment 57513View attachment 57503View attachment 57514 turned out well i think upto now and begining to come together.

cheers steve

View attachment 59444

View attachment 59445

View attachment 59446

View attachment 59447

View attachment 59448

View attachment 59449

View attachment 59450

View attachment 59451

View attachment 59452

View attachment 59453

View attachment 59454

View attachment 59455

View attachment 59456

View attachment 59457

View attachment 59458

View attachment 59459

View attachment 59460

View attachment 59461

View attachment 172470

View attachment 172471

View attachment 172472

View attachment 172473

View attachment 172474

View attachment 172475

View attachment 172476

View attachment 172477

View attachment 172478

View attachment 172479

View attachment 172480

View attachment 172481

View attachment 172482

View attachment 172483

View attachment 172484

View attachment 172485

View attachment 172486

View attachment 172487

 

[Guest]

Nice job Steve.

Andy

 

[Guest]

Cheers Andy quiet pleased with the way things are going just now the grattings and belaying pins i ordered turned up yesterday so i will be able to crack on with things when i get back home from sea and while im away will be doing my best to keep a eye on your build.

steve