discussion How I Build Dioramas in 1/16th.

[Guest]

Wood bending tool. I use an old hair curler for bending wood.It remains at a nice constant temperature and has just the right curve for most hobby work.

I dunk my wood into water and let it soak for awhile depending on the thickness.Then I press the wood up against the curler and slowly bend it to shape.If you are bending right near the end of the wood get an old piece of wood or the end of an eraser to replace your fingers.Take your time and re-soak the wood if necessary.Even thin wood has a grain and some of it does not run lengthwise but is cross grain in nature,so if it keeps breaking select another piece.If the wood splits turn it over and bend the other way.After a while you will become more familiar with the grain of the wood just by looking at it.Experiment and take your time! Have fun.

 

[Guest]

Wood bending tool. I use an old hair curler for bending wood.

What a brilliant good idea if you dont mind John I am going to copy this to the tips page

 

[Guest]

I've just gone through a process of bending strips of 1mm x 1mm wood and I used a tin can after soaking in hot water but the idea of using hair curlers is a brilliant one.

I'll give it a go, thanks for the idea!

 

[Guest]

[No message]

 

[Guest]

Glueing up the wing. The upper wing has been glued up using super thin super glue at all the joints and in between the bend laminated wood strips.The capillary action of the thin glue allows for all parts to be glued while pinned down to the building board.

Where the wing tips join the leading edge I made a 45 deg cut.

Let the glue cure for an hour or so and then the wing can be freed from the building board.Give it a quick check for any loose joints and apply more glue where necessary.Now it is on to the sanding.

Note: there is a pic on my photobucket site that shows the underside.The four rib from the front shows some deformation where the cap strip fits over the spar.I couldn't see this until after the wing was removed.It was probably caused by the rib installation somehow getting out of sequence when they were installed over the tapered spar.Normally I would replace it but this being a wreck I will make it a stress fracture.

There are many areas that could be improved in the fitting of the wood parts etc... I could without too much effort scratch the ailerons etc...but on a large project such as this I can't allow myself to get bogged down into too much detail that will never be seen upon installation.You have just got to draw the line somewhere and modeling for God is that line for me!This is not an excuse for poor modeling just reality if I ever hope to get anything finished.

 

[Guest]

What a brilliant good idea if you dont mind John I am going to copy this to the tips page

No problem! Glad you like it.

 

[Guest]

[No message]

 

[Guest]

The sled. The wreckage rests upon this sled and was dragged by horses or a truck to the spot beside the hangar.The wreckage had been ordered off the field right away with no time to even cut the control wires and remove the tail.

It is now being stripped of any usable parts and the rest will be sent to the junk pile.

 

[Guest]

[No message]

 

[Guest]

[No message]

 

[Guest]

I used my usual barn siding technique on the raw wood for the aging process and then used pastels for shading.I will leave it at this for now until I mount the engine and then will add oil spots,rusty nails,chains for pulling etc...The sled is the base upon which the rest will be built.

I have decided that there will not be a lot of fabric left on the wings or control surfaces other than a few burnt remnants.Why? because I want my viewer to be able to get a good look at the skeleton aircraft and how it was built.The plywood fuselage aft of the cockpit will give me ample opportunity to add a little color to an otherwise pretty drab scene by putting on some national and other markings.

 

[Guest]

I think the ages and weathered wood looks particularly effective. What do you mean by the "Barn Siding Tchnique" because it works very effectively.

 

[Guest]

[No message]

 

[Guest]

The wing tips ,trailing edge and bent center section are finished.I did a little more scorching of the wood but will let it go at that for now ,until after I mount the front section of the fuselage and decide on the burn pattern. __________________

 

[Guest]

[No message]

 

[Guest]

Burned fabric remnants. Here is a great example of flash burning of the fabric on a wooden aircraft.

How much fabric to leave attached is a judgment call,in my view.

Some photos show an almost complete burn, others varying degrees of burn.

I think that the determining factor for me will be just how much color I want to add to the scene.

The little model above shows just enough color to be able to identify some of the squadron and national markings which is probably more important for an aircraft set in a field.My wreck is set in a diorama where this would be quite obvious.

Another consideration , in salvaging some of the parts ,would most of the remnants of fabric have been already torn off by the salvagers.Also, I can't imagine any base commander wanting a wreck hanging around for any length of time, especially if it was showing half burned squadron or national markings. Not good for morale,I would think.

 

[Guest]

Hello John

Not meaning to sound silly but what about actually burnnig the covering and protecting what stays un-burnt with water

 

[Guest]

[No message]

 

[Guest]

This is Fritz the dogs eye view of his masters wrecked airplane.The whole storyline is based upon this relationship and is what inspired me to expand this diorama in the first place.I will leave it to the viewers imagination as to whether his master survived to fight another day.

I was never very happy with the original diorama after building the other two.The story was weak,two pilots looking at a mechanic wiping down an engine after a run-up.Pleasant to look at but no real emotion.Now the main storyline is transported outside the confines of the hangar.What I am hoping is that the average viewer will initially be drawn to looking inside and only later discover the dog/man story outside.The hangar doors will be left open thereby somewhat hiding from view the real story.

At the same time I want the aircraft to be somewhat educational, in that I don't want to cover the structure with fabric.The fuselage being plywood I can leave off a few panels here and there to make it more interesting for those who may want a peak inside.

The fuselage broken at the cockpit with the hanging seat belt straps really adds to the pathos of the scene.The tail having been pushed over the lower wing suggests some sort of pilot resue attempt which would have really had to be done in haste if a fire was just breaking out.The fabric on the tail would then also have been involved in the flash over burn.

The wings are remarkably intact which suggests to me a low impact type crash or nose over.

I will leave it up to the imagination of the viewer as to what really happened, which is after all the real purpose of of any good diorama storyline.

 

[Guest]

[No message]