Scale Model Shop

Collapse

SE5a CONSTRUCTION BEGINNING TO . . .

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • Greyhead
    • Oct 2004
    • 581

    #481
    This post is not about a part of the model itself but non the less important for that!


    The ailerons need to be joined by a length of thin piano wire, at this scale “quick links” are a non-starter mainly because of their size but in any case there are no detachable linkages on the full size Se5a. Therefore the upper and lower wings will be permanently fixed together by the interplane struts and the aileron linkage; I don’t haven’t enough room to be able to keep the model permanently rigged so this could cause a problem for storing the wings when removed from the fuselage.


    I’ve made 2 frames to support the inner sections of the wings; they are in 2 parts and held together with removable pins.





    The wings will be stored “hung” from brackets by the top wing, the lower wing supported by the interplane struts and the frame, which grips the trailing and leading edges.





    To assemble the model the wing locating pins are pushed a little way into the holes in the centre section and wing stubs, which then take over the support of the wings.





    The pin is then removed and the frame disassembled, the aileron controls connected and the wings finally pushed home and the wing retaining grub screws tightened.





    That’s the theory anyway!
    Attached Files

    Comment

    • Guest

      #482
      This is one of those rare models that really does deserve the description of "Museum Standard". She is looking superb Grahame and I can't wait to see a couple of shots of her in the air.

      Comment

      • Greyhead
        • Oct 2004
        • 581

        #483
        I’m still searching for things to do whilst waiting for the paint to arrive; I hadn’t intended to do this job until much later in the build but needs must etc.


        The piano wire, which links the ailerons, has to be the correct length to ensure the ailerons themselves are at the same angle relative to the main planes. Although they are drawn on the plan I prefer not to rely on these but to make them to fit the actual model; a build-up of tolerances (euphemism for building errors!!) can result in the drawings and model not exactly matching, so first I made an adjustable link.


        The landing wires are attached to ensure the correct dihedral angle, the ailerons held at neutral with spring clamps and the link adjusted to the correct length.





        The adjustable link is made from a couple of bent pins soldered to some brass screw clamps from my “useful items” box and a length of 2mm rod. Once locked at the correct length the aileron clamps are released, the link removed and a piano wire link bent to the same length.





        Fitted in place the link looks a lot better than a 2mm rod attached to control horns by quick links.





        When the links are permanently fitted the hole in the Solartex will be covered using a frayed tape with a slot in it, but this will be about the very last thing to do to the model, it won’t be done until all the painting etc has been completed and the wings are joined as a single unit.
        Attached Files

        Comment

        • Guest

          #484
          looks beautiful grahame learned a lot of nice tricks will help me with my totally scratch built 3rd scale Bristol Fighter. Thanks for such an informative thread. my website is http://www.proflooney.net I will be starting the bristol build in a couple weeks but in the design section I been doing a detailed design thread. on my site is also one for my 1/3 scale gotha V Bomber I am designing and about to start too it has a mere 26 ft ws and i already started using several tips I learned from you to flesh out certain areas of both planes I was figuring out how to do them well.

          Joe

          Comment

          • Guest

            #485
            Joe,

            Good to see you here as well. How are the Bristol and Gotha coming along?

            James.

            Comment

            • Guest

              #486
              Hi James they going good waiting on parts for both and trying to get ahold of the flair nose section former drawings and the nose section plans for the bristol as I like the nose on it very scale outline and that should finish up the bristol design for the most part. thats the area giving me fits trying to get right.

              Comment

              • Greyhead
                • Oct 2004
                • 581

                #487
                I always use silver Solarlac to fuel proof the engine bay; firstly because you can see where you’ve been and more importantly where you’ve missed and also because it shows up any places where the joints are less than perfect and believe me there’s quite a few of them!





                You can see where the corner of the engine bearer meets the former there is a slight gap; it’s not a strength issue at the moment but the crevice could hold fuel / oil and eventually it would soak into the wood and cause problems. I’ll fill it and any others with epoxy / micro balloons then give it another coat of Solarlac.
                Attached Files

                Comment

                • Guest

                  #488
                  what are these "micro balloons" you talk of?

                  ....im guessing they are tinny little ballons lol but any technical info/pics/discription and how/what they are used for would be great!

                  Comment

                  • Greyhead
                    • Oct 2004
                    • 581

                    #489
                    Richard

                    Although the grammar doesn’t sound good I think the best description would be that micro balloons is a very fine powder; whether or not each grain is in fact a hollow sphere I’ve no idea but it is very light though not “spongy” like polystyrene. It is used to “bulk out” glues, typically epoxy; it becomes more capable of gap filling as it makes the glue into a stiffer mix without adding too much weight. I’ve also used it to “mould” simple shapes by mixing enough micro balloons with epoxy to make a very stiff mix, waiting until the epoxy is starting to cure and then forming the shape with my fingers; a final sand once fully cured finishes the job.

                    Grahame

                    Comment

                    • Guest

                      #490
                      yes grahames correct. basically microballons is kind of a thickening agent which helps the epoxy hold shape. it is commonly used to create fairins etc. other agents that work similar are talc and cabosil.

                      Comment

                      • Greyhead
                        • Oct 2004
                        • 581

                        #491
                        How much “weathering” is appropriate, if any at all, is a matter of personal preference; I like my models to look as if they’ve seen a fair amount of action, others like a pristine, ex-works finish. Also you can see that the lettering looks obviously hand painted, as it should do for a WW1 aircraft; accurate, computer generated transfers just wouldn’t look right.





                        Some of my comments during this thread such as “ I don’t worry about the odd scratch or dent” may have given the impression that a “weathered” finish is an easy option, I can assure you that it isn’t! To get the correct amount of wear and /or damage in the correct places so as to make the model look “real” is a work of art in itself. Some scratches and dents can be left; others can’t and have to be repaired.
                        Attached Files

                        Comment

                        • Guest

                          #492
                          Originally posted by \
                          “ I don’t worry about the odd scratch or dent” may have given the impression that a “weathered” finish is an easy option, I can assure you that it isn’t!
                          That is very very true, espeacially at AFV models. Some people say that when you build a tank as an example, you can get it really wrong, and you can still make it look acurrate. The heavy weathering might mask many mistakes, but that isn't a reason to make it look more "dirty".

                          To get the correct amount of wear and /or damage in the correct places so as to make the model look “real” is a work of art in itself. Some scratches and dents can be left; others can’t and have to be repaired
                          I also agree with this. At a World War I plane there is a lot of friction. For an acurrate plane you surely have to work a lot at weathering. Some people like their models to be "clean"... it's ok, but they have nothing special, unique, and that's the part where you show your skill.

                          Great job! I admire your work.:bravo:

                          Comment

                          • wonwinglo
                            • Apr 2004
                            • 5410

                            #493
                            That serial looks spot on,that is exactly as they painted them in the field during WW.1

                            Comment

                            • Greyhead
                              • Oct 2004
                              • 581

                              #494
                              Although WW1 aircraft were not spray-painted, one substance certainly was liberally sprayed about and that was oil! This is where things can go horribly wrong; having spent a fair amount of time painting the model it needs to be “dirtied up”, paying special attention to any white areas. An error now and it’s a re-painting job.


                              Ideally I’d have finished all the painting before I started on this stage but as I’m still waiting for the PC10 I’ve made a start where I can. Here’s the rudder after this second stage of weathering.





                              I apply the paint, which is very watered down, with a rag and wipe it in the direction of the airflow slowly building up the “dirt” to what I consider to be an appropriate amount.


                              The under surfaces of the tail plane really get the treatment, as will the under surfaces of the fuselage and the lower wings.





                              It is impossible, because of the lack of quality of photographs from the time, to be sure just how weathered / dirty these aircraft became in service but it is clear that the fields got quite muddy so I think it’s a fair bet that the aircraft themselves got equally dirty.
                              Attached Files

                              Comment

                              • Guest

                                #495
                                i have to say grahame that looks unbelievable! it looks perfect and exactly to scale (the weathering i mean) if i didnt know better and ignored the unpainted part, i would think i was looking at a photo of the real plane in colour!!

                                lovely job i cant wait to see the other finished sections!

                                Comment

                                Working...