HI Sue glad you think so but im not really happy with it but hopefully it will look ok when sprayed grey an thanks for lookin in stay safe
chris
boatman's 1/72 HMS Tiger C20 build
- Thread starter boatman
- Start date
chris
close up shot 
strb side shot an these pipes
were little buggers to get the right angels before i gluded them in place an had to be carefull with the glue as the funnell must come off
were little buggers to get the right angels before i gluded them in place an had to be carefull with the glue as the funnell must come off
now shots of it mounted on the main 01 deck 
an port side angle shot 
proper port side shot
Chris,
One thing you could try is to put a spring inside the tube to support the walls as you try and bend them. like a plumbers spring. Or nicking the inside of the bend.
One thing you could try is to put a spring inside the tube to support the walls as you try and bend them. like a plumbers spring. Or nicking the inside of the bend.
an here in the last pic today a shot of this small gantry platform an this was a devil to build but hey it worked out ok an its only 1/4 of an inch depth an talk about fiddley an in case anyone is wondering where the wires are for the Anti /collishion lights they are goin down inside the funnell an at the moment this funnell is a dummy but if i have the room i may buy another smoke unit so both funnells smoke or steam but will see on that 
YES Scottie very good idea on that but this lot is all glued down now but i might try your idea on the front funnel pipes but the bends are so tight i would have loved to done these in brass tubein but i havnt got the bendin tools to do this
Not sure of the diameter of the pipes, but if you used a bendy straw, i
I'm guessing 6-7 mm? If you can get to a garden centre of flower shop, you can get soft bendy wire covered with a soft 'rubbery ' plastic. Might be something you could use...
I'm guessing 6-7 mm? If you can get to a garden centre of flower shop, you can get soft bendy wire covered with a soft 'rubbery ' plastic. Might be something you could use...
HI Ian cheers for that idea but ive now only got to fit the front funnel tube an they are very easy an short nothing like the rear ones as by rights the big tubes shoild be about 2mm bigger in diameiter but i think i looks a bit weird to me as its the black tubes standing out against the white funnell plasticard so i think it will all look ok when it in grey an it matches up in colour an looking at the plans these pipes wont be seen much as they will have the seacat missle lauches an the target directors in front of them so no worries
but cheers for havin a look in
an same to all you guys an gals
stay safe
chris
NO thats not the problem Tim its just the pipes should be 2mm bigger in diameter but they will now do as they wont hardly be seen
CHEERS for lookin
chris
Chris. Nice updates you been at this for a long time keep chipping away at it
OH Cheers for that Rick an the other guys sayin that has made me feel a little better as i like to try an get things right as near as possible but sometimes we have to take what we got hav'nt we anyway as i said in the other post they may not be seen much as a lot is still to go on the deck in front of them an thanks for your comment
ATB Chris
AN HI ALSO TO YOU TO Lee yea its been a long build so far an not even half way yet so for now im leaveing the rear funnell even though its still got to have all the ladders on it but they will go on after it been sprayed grey so next up is the really hard front funnel as this one will be steamin an will need to have the flexi tube fitted to it an then down to the smoke or steam unit an this is goin to be hard a i cant see in the S/S TO line it all up so thinking cap on for the next wk or so tryin out different ideas
ATB an hope you feel better Lee
chris
THANKS Peter im always striveing to the finish line which is not even a light at the end of the tunnel yet so onwards an up
Legal Notice
scalemodelling.co.uk is a privately operated online discussion forum. All content posted by members reflects their own views and opinions and does not necessarily represent those of the forum owners or administrators. While reasonable efforts are made to moderate content, no responsibility is accepted for user-generated material. By using this site, you agree to comply with UK law and the forum rules.