G
Great work so far Paul, you're definitely putting in the hours on this one!
You could always save yourself some work by posing the hatches open?
You could always save yourself some work by posing the hatches open?
Paul's (tricky) Normandy Panthers in 1/35 & 1/16
- Thread starter tr1ckey66
- Start date
- Status
B|Did a little work on the hatches last night. I've fabricated new hatches from plastic card, a process complicated by the need to laminate 2 weights of card to get the thickness of hatch required to sit level with the deck. All i need to do now is remove the fittings from the resin items and fit to the plastic card replacements.
Or is it?...
I had a nagging doubt in the back of my mind whilst doing this work, and this doubt proved to be correct - the hatches are now too thick. You can see the problem in the comparative photographs below.
Essentially, the Tamiya hull is too deep to simply fabricate hatches of the same thickness.
There are 2 possible fixes:
1. Raise the lip inside the holes for the hatches to reduce the height to the deck. This will be incredibly difficult to do
2. Rework the entire removable section that contains the hatches as indicated below
I think I'm going to go with the latter option but this may be a weekend job now!
Till then
Cheers
P
Or is it?...
I had a nagging doubt in the back of my mind whilst doing this work, and this doubt proved to be correct - the hatches are now too thick. You can see the problem in the comparative photographs below.
Essentially, the Tamiya hull is too deep to simply fabricate hatches of the same thickness.
There are 2 possible fixes:
1. Raise the lip inside the holes for the hatches to reduce the height to the deck. This will be incredibly difficult to do
2. Rework the entire removable section that contains the hatches as indicated below
I think I'm going to go with the latter option but this may be a weekend job now!
Till then
Cheers
P
G
wow!
Magnificent work so far Paul :x :x
Magnificent work so far Paul :x :x
Complete driver's and radio operator's hatches
Hi everyone
Well, this area of the build certainly took longer than I anticipated!
To recap, I decided to rebuild the Wecohe hatches and part of the deck to resolve fit and scale issues. I finally finished this area today and the results can be seen below. I built the deck with 2 weights of plastic card and detailed it with bolt holes and the rebates for the hatches themselves. The fittings from the original Wecohe items were removed and placed on to the new plastic card hatches. I did rebuild some of the detail, again in plastic card, simply because it was easier to do this.
Because the items have rounded edges lots and lots and lots of test fitting went into this part of the build and i'm happy enough with the results..
Next: Hull texture and Zimmerit!
Cheers
Paul
Hi everyone
Well, this area of the build certainly took longer than I anticipated!
To recap, I decided to rebuild the Wecohe hatches and part of the deck to resolve fit and scale issues. I finally finished this area today and the results can be seen below. I built the deck with 2 weights of plastic card and detailed it with bolt holes and the rebates for the hatches themselves. The fittings from the original Wecohe items were removed and placed on to the new plastic card hatches. I did rebuild some of the detail, again in plastic card, simply because it was easier to do this.
Because the items have rounded edges lots and lots and lots of test fitting went into this part of the build and i'm happy enough with the results..
Next: Hull texture and Zimmerit!
Cheers
Paul
G
That is some cracking detail on those hatches.
Tube container for barrel cleaning rods and antenna
This post was going to be about hull texture and Zimmerit, but the application of this coating requires knowing where the various brackets and clamps will be located. To do this I'll have to finish most of the photo etch first to ensure their positioning is correct.
So...
Today I finished the tube container found on the left hand hull side of most Panthers (crews of certain units moved theirs to the back of the rear deck). This tube was used to house the barrel cleaning rods and the antenna.
This Aber photo etch set took another day of soldering but is, I think, infinitely better than the kit part. Again all the clasps work and although occasionally frustrating I think the extra work was really worth it.
Here's a few pics...
The kit part for comparison...
And the part below where it will eventually be positioned on the tank...
Next...
More soldering I'm afraid with tool brackets, fire extinguishers, jacks etc on the menu!
Till next time
Paul
This post was going to be about hull texture and Zimmerit, but the application of this coating requires knowing where the various brackets and clamps will be located. To do this I'll have to finish most of the photo etch first to ensure their positioning is correct.
So...
Today I finished the tube container found on the left hand hull side of most Panthers (crews of certain units moved theirs to the back of the rear deck). This tube was used to house the barrel cleaning rods and the antenna.
This Aber photo etch set took another day of soldering but is, I think, infinitely better than the kit part. Again all the clasps work and although occasionally frustrating I think the extra work was really worth it.
Here's a few pics...
The kit part for comparison...
And the part below where it will eventually be positioned on the tank...
Next...
More soldering I'm afraid with tool brackets, fire extinguishers, jacks etc on the menu!
Till next time
Paul
G
That tube container is an absolute work of art Paul! You've got the skills to pay the bills 
Tool Brackets
The marathon soldering session continues!
Finished the left hand hull tool bracket today. Well, almost! There's still a couple of retains pins and connecting chains to assemble. I'm also going to fashion a new shovel handle out of real wood a little later on in the build.
Anyway here's the progress...
Cheers
Paul
The marathon soldering session continues!
Finished the left hand hull tool bracket today. Well, almost! There's still a couple of retains pins and connecting chains to assemble. I'm also going to fashion a new shovel handle out of real wood a little later on in the build.
Anyway here's the progress...
Cheers
Paul
G
Very neat indeed
Bob
Bob
G
Really detailed build post Paul.
G
brilliant work mate, been off forum recently, the prolifereation of PE and AM make this into a stunning build
- Status
Legal Notice
scalemodelling.co.uk is a privately operated online discussion forum. All content posted by members reflects their own views and opinions and does not necessarily represent those of the forum owners or administrators. While reasonable efforts are made to moderate content, no responsibility is accepted for user-generated material. By using this site, you agree to comply with UK law and the forum rules.