discussion Rick's Airfix 1/72 English Electric Lightning F6

[rickoshea52]

Box and sprue shots


View attachment 239646


View attachment 239647


View attachment 239648


View attachment 239649


View attachment 239650


The detailing kit


View attachment 239651


The first cut is the deepest. The panels marked are the ones that I plan to drill and file out but this depends on practicalities.


View attachment 239652


View attachment 239653


View attachment 239654


View attachment 239655


With the engine bay panel drilled and filed out the first trial fit of the resin engine can be done. The belly ventral fairing comes as a separate moulding in the kit and I may attempt a scratch built No.1 engine and leave the belly fairing off.


View attachment 239656


View attachment 239657

 

[takeslousyphotos]

I do like the lightning Rick....... I`'ll have to watch this mate.

 

[Guest]

I was thinking about getting this kit while in Hobbycraft a few days ago, so I'm watching with interest Rick

 

[rickoshea52]

I was thinking about getting this kit while in Hobbycraft a few days ago, so I'm watching with interest Rick

You could have got one for a tenner from Airfix last week. I built the F2 last year and really enjoyed it. The intake assembly on these need some care, there are ejection moulds on the inside of the fuselage that I think are fouling and preventing the nose coming together nicely. I'll trim them off when I get home with a dremel and re-check the fit.

 

[papa 695]

I'm in watching this one Rick the Lightning is one of my favourite aircraft, and I'm really liking the addition and alterations your doing to this.

 

[Guest]

Will be watching this.


My Dad worked on the Lightning,he was an aircraft fitter.

 

[Guest]

This is looking very good

 

[Robert1968]

Ohhh I like this I thought that the new mould was going to be good from Airfix but your doing a cutaway with engine showing now that's perked me up on attention. The cuts seem to be very good ( was the plastic soft enough) Airfix new plastics seem to be not as brittle as older Airfix kits ( my opinion )


I'm in on this


Robert

 

[flyjoe180]

The engine fit has gone well Rick.

 

[Guest]

Nice progress Joe, i'm watching you, cheers

 

[Guest]

Just found this and you got me interested, I have my chair ready.... and cracking work so far.


scott

 

[colin m]

I'm looking forward to this one. There is a chance Santa might be bringing me one of these...................................

 

[rickoshea52]

I started to add some scratch built detail to this as well as one of the resin castings, the avionics bay on the opposite side will need some more work. When it's painted it should look a bit more realistic.


The intake trunking needed some of the width trimmed off using a dremel and sanding drum as well as the inside of the fuselage to make the nose come together as the two halves had a gap.


View attachment 241511

View attachment 241512

View attachment 241513

 

[Guest]

Very impressive work going into this.

 

[rickoshea52]

Getting the interior to fit on this kit is really troublesome, probably caused by the resin part and the hacking and bashing but I finally have the cockpit fitted to one half of the fuselage. Before fitting the other half some more dry fitting and scratch work will be required, the top will have a resin engine on view and I'd like to do something with the bottom, maybe a scratch built engine and leave the ventral fairing off to add interest. This will require making a frame for the aft part of the opening and detailing the exposed section at the forward end - all will become clear as this progresses.....I hope.


View attachment 242246

View attachment 242247

 

[PhilJ]

I like where your going with this one Rick, I'm now watching the thread

 

[papa 695]

Some nice work Rick

 

[takeslousyphotos]

Very nice Rick ........ This is looking good mate.

 

[flyjoe180]

Looking good Rick.

 

[BrianT]

I'm in. This is one of my favourite aircraft I saw this at Biggin in the early 60's and remeber it vividly to this day