discussion P51 D from Zoukei Mura

[Guest]

Hi comrades!
It has been a while since my last post. I even found that the whole webpage has changed!
Anyway I have been modelling all this time, don't think I've been lazy, so I will be posting some of the models I've built.
Here you have a superb P51 from a Japanese brand called Zoukei Mura:

View attachment 322020
The best of this model is that it has each and every little detail from the inner structure, engine, machine gun bays... you'll see.
Even the instructions manual is full of detail, as if it was a contemporary document:
View attachment 322021
View attachment 322022
Following the instructions, I started off with the engine. Just check the crazy level of detail... they even moulded the pistons!


View attachment 322023

So step by step, I built the engine block, the first part of the transmission and the intake manifold:
View attachment 322024
View attachment 322025
View attachment 322026
Then I glued the two cylinder blocks and the crankcase:
View attachment 322027
And here you have it alltogether, along with the propeller shaft:
View attachment 322028
On the back of the engine I glue the fuel and oil pipes, as well as other little details:
View attachment 322029
I also build the tuebocharger:
View attachment 322030
And here you have the three main parts already covered with black primer: engine, turbocharger and crankshaft cover:
View attachment 322031
Just some shots of grey primer in order to create a simple light/shadow scheme:
View attachment 322032
And then the main paintjob in a grey/blueish scheme. As you can notice, I highlited the bolts and main lines and left the cylinder cover in black:
View attachment 322033
Next step, I put a decal and applied some washes with a very dilluted mix of brown and black. I also added the water coolant tank and the alternator:
View attachment 322034
Above the engine I added the oil and fuel pipes:
View attachment 322035
Time to put it all together:
View attachment 322036
View attachment 322037
And more pipework (I think these wre for the sparks):
View attachment 322038
And then I added the exhaust cover and ignition cables:
View attachment 322039

 

[Guest]

Well, it seems I only can add 20 images each time.
Let's continue with the exhaust pipes, painted brown as if they where burnt by the exposure to heat:
View attachment 322040
With that, the main part of the work in the engine is done, so next step, will be the firewall, engine frame and oil tank:
View attachment 322041
I painted them with a tone of yellow, very similar to the imprimation they used in the North American factory:
View attachment 322042
But my dear P51 has seen many combats over the european skies, and has been manipulated by many mechanics so I put some grime to make it look a little bit more real:
View attachment 322043
I painted the oil tank in bright yellow:
View attachment 322044
And, as I'm going to place a pair of mechanic, figures, I decided to imitate an oil leakage for them to fix:
View attachment 322045
Then I glued it all together, firewall, engine and frame:
View attachment 322046
View attachment 322047
View attachment 322048
View attachment 322049
And that's how cool it looks the Packard V-1650, the american version of the superb Rolls-Royce Merlin!

Now, let's aim for the cockpit!

I started with the cockpit floor. As I learned, the cockpit floor was made of wood but it was painted black, so I decided to imitate that. First, I painted the floor in deck tan, and then I gave some brush strokes with dark brown and red brown oil paints:
View attachment 322050
Then I painted with Tamiya orange glaze:
View attachment 322051
Afterwards, I covered it with future, hairspray and matt black:
View attachment 322052
And why the hairspray?? Because with a toothpick, a brush and some water I can imitate the scratches:
View attachment 322053
Then I painted the rest of the floor with interior green and I applied some dust:
View attachment 322054
I followed painting all the rest of elements also in interior green:
View attachment 322055
View attachment 322056
With yellow primer and steel I paint the scrathes and marks left by the parachute hilts in the seat:
View attachment 322057
I completed the seat with dark green for the cushion, black for the upper part and tphotoetched belts:
View attachment 322061
And in the back... I glue the heating system:
View attachment 322062

 

[Guest]

Next step: I put the fuel tanks and the frame for the battery and the radio with the admission pipe and fuel indicator:
View attachment 322063
For the gauges I used the decals and some paint:
View attachment 322064
Then I painted the central console and I added the pedals:

View attachment 322065
Then I painted the sides and added some decals:
View attachment 322066
Time to bring it all together again:
View attachment 322067
View attachment 322068
View attachment 322069
View attachment 322070
I added the radio and battery:
View attachment 322071
And that's how a mustang looks like without skin:
View attachment 322072

That will be all for today!

 

[papa 695]

That is looking sweet, and nice to see you posting again.

 

[scottie3158]

That's a crazy level of detail and you appear to be doing it justice, nice work.

 

[colin m]

You're doing a great job there with that amazing level of detail. But pistons - what was the manufacturer thinking !

 

[BarryW]

You're doing a great job there with that amazing level of detail. But pistons - what was the manufacturer thinking !

It is their little ‘quirk’, almost a trade mark.

 

[BarryW]

you are dong a great job Judas. Be careful fitting the airframe, dry fit and keep dry fitting at least two steps ahead. It is easy to get a small misalignment that has a knock on effect with this engineering. It is a great kit though.

 

[Guest]

you are dong a great job Judas. Be careful fitting the airframe, dry fit and keep dry fitting at least two steps ahead. It is easy to get a small misalignment that has a knock on effect with this engineering. It is a great kit though.

Hi Barry!
Well, I finished this kit a while ago, but as you've said, I had some fitting problems I could manage at last (Well, you'll see)
Thanks anyway!

 

[Guest]

Let's continue!

I primed the pipes and elements that conect the engine with the oil and coolant radiators:
View attachment 322236
Then I painted them with Alclad metallics, which I think is the best option for doing metallics.
It has its pros as for example its supersmooth finish, but also has its cons, as it is truly revealing if any mistake during building or sanding was made:

View attachment 322237
Anyway I left this part like that because it has a cover, is going to be placed in the belly of the plane, and it won't be seen. Here I glued everything in place:
View attachment 322238
And then I add the coolant radiator:
View attachment 322240
And the oil radiator:
View attachment 322239
And just below the engine I glued the intake for the supercharger, also painted with alclad laquers and weathered with oils, Here you can also see the final conection of the coolant pipes with the tank just above the transmission and propeller shaft, which was quite tricky as it didn`t want to fit in place:
View attachment 322241
Then I primed the wing structure:
View attachment 322242
I painted the main fuel tanks:
View attachment 322243
At that point I knew I wanted to left open at least one of the machine gun bays and I didn't realize that the tanks couldn't be seen, but anyway it didn't took so long:
View attachment 322244
Then I painted the cal.50 machine guns with black primer:
View attachment 322245
Then steel:
View attachment 322246
Black wash:
View attachment 322247
And graphite from a regular pencil:
View attachment 322248
Then, the loaders and ammo belts. As I heard in a documentary, ground crews used to fit some tracing ammo between regular rounds in order to allow the pilot to track their fire, so I painted red one of each five rounds:
View attachment 322249
Then I fit everything in place:
View attachment 322250
Now, lets put some wings into the main strut!
View attachment 322251

Well, this was mainly for the pictures, as the fuselage and wing panels must be cover the structure before joining them together.

 

[Guest]

Let's begin with that lovely silver skin of the mustang!
As you can see in this picture, I used three or four different tones of aluminium to have variety in the fuselage:
View attachment 322252
View attachment 322253

View attachment 322254
View attachment 322255
This wouldn't be a mustang if it doesn't have a colorful livery, so I masked part of the cowling:
View attachment 322256
View attachment 322257
And I painted it in brilliant red:

View attachment 322258
View attachment 322259
I made some scratches:
View attachment 322260
View attachment 322261
And then I placed everything over the fuselage strut:
View attachment 322262
On the left side I made the same, but using the parts of the models without the cowling:
View attachment 322263
And this is the big problem Barry warned me about...
The model allows you to build the nose with or without the engine cowling. But this "Frankestein" I decided to make, mixing both options... it just doesn't work because it leaves quite big gaps between the wing and the fuselage as you'll see.
But first, I had to place the windshield, so here you have the windshield process:
Masks:
View attachment 322264
Interior green:
View attachment 322265
And aluminium
View attachment 322266
I also painted the anti-glare band of olive green in the nose.
This olive green paint used to flake and change colour with the exposure to sunlight and rain, so I used the salt technique to imitate that.
First I paint a light tone of olive drab, then I shot some water and just add salt:
View attachment 322267
And then I painted the normal tone of olive drab. Once you remove the salt and paint some chipping, this is the result:
View attachment 322268
I had to replace the mask between colous and that left a small gap I tried to minimize with an oil wash (with poor results).

Well, that's all for today...
Regards!

 

[Guest]

Let's continue after a long Christmas break!

I made some chipping in the frontal coil:
View attachment 326147

Then I continued with the wings, starting with the main gear wells:

View attachment 326148


View attachment 326149
View attachment 326150
View attachment 326151
Then I painted some layers of aluminium lacqer from Alclad:
View attachment 326152
After that, I glued the outer pannels to the inner structure:
View attachment 326153
I used some masking to imitate the metal stress in the flaps (just as an experiment)
View attachment 326154
View attachment 326155
I also added the red wingtips:
View attachment 326156
I also worked on the main gears:
View attachment 326157
View attachment 326158
I used steel cable to imitate the hydraulic brake system:
View attachment 326159
And then... the marriage, joining the wings to the main fuselage:
View attachment 326160
The right side didn't look so bad, but the left side...
View attachment 326161
It certainly needed make up... this is what BarryW just said some weeks ago about misalignments.
This is what I did: First, masking:
View attachment 326162
After that, I worked with putty and green stuff:
View attachment 326163
Then, sanding and engraving:
View attachment 326164
And finally painting, and this is are the results after the make-up operation:
View attachment 326165
View attachment 326166
In addition, I will use some other tricks to mask this fitting misalignments, but I'll leave that for another day

Cheers!

 

[rtfoe]

You sure know how to get into the thick of things Judas. :smiling2: Good come back. :thumb2: With the price and detailing of a Zuokei kit I thought they would at least made the third option viable. I guess all the attention was on the engine.

I went thru all your steps...lovely and interesting using yellow and staining it rather than straight out of the bottle zinc chromate...saves on highlighting. It's looking real good so far. :thumb2:

Cheers,
Richard

 

[scottie3158]

This is coming on nicely.

 

[Guest]

Thanks for your kind comments guys!

Let's keep going with this mustang.
I finished the main gear wells, with all the piping and lights:





Then I started with the propeller:
Black Primer:


Marks and stencils:


Yellow tips, scratches and weathering:


Then a beautiful red spinner:


And finally the propeller in place:


I continued with the nice bubble canopy:




As the mustang was used mainly as an escort fighter, I decided to add two external fuel tanks.
Again, black primer:

A nice aluminium layer from ALCLAD:


Some decals:





And fuel stains:


Then I continued the dull work of placing the decals all over the model with Micro Set and Micro Sol:


And here is the result:


Just some minor details left and I'll post it into the finished models thread!

Regards!

 

[Vaughan]

A great build, the quality of workmanship is outstanding.

 

[Guest]

Magnificent work Javi!!! :thumb2:

 

[papa 695]

Just caught up again, and this is one seriously good looking build.

 

[Guest]

Thanks for your comments friends!

Let me tell you how I finished the model:
I completed the machine gun wells, keeping one of them open. You can also notice that I marked all the engraved panel lines with a light oil wash, insisting in the fuel intakes:


I used the airbrush for the smoke trail coming out from the exhaust:


In order to give a scale sensation and cover up some misalignment mistakes, I asked these guys for help:


I just painted with the usual olive drab, trying to give a scruffy look, with oil stains, some dust...



And that's it!!!
I'll post some pics here, and the rest in the finished aircraft thread:




I hope you enjoyed it!

Regards!

 

[Vaughan]

Great build, beautiful detail what more can I say.