discussion Which airbrush would you buy?

[LeytonO]

Beware of the wire cleaning brushes that look like a miniature chimney sweep brush.
Much better to use something like this https://www.waitrose.com/ecom/products/tepe-easypick-m-l/792885-658635-658636

 

[PaulTRose]

I'm poor..... I go to Lidl for mine

 

[LeytonO]

I'm poor..... I go to Lidl for mine

You might not if Waitrose was a five minute walk as opposed to a 7 mile drive each way to the nearest Lidl.
Do go there sometimes though, their Bratwurst are excellent and Gammon joints are nice too.

 

[PaulTRose]

You might not if Waitrose was a five minute walk as opposed to a 7 mile drive each way to the nearest Lidl.
Do go there sometimes though, their Bratwurst are excellent and Gammon joints are nice too.

Out of interest I just looked where the closest Waitrose is to me..... 36 miles away

 

[LeytonO]

Out of interest I just looked where the closest Waitrose is to me..... 36 miles away

Bit further than my 482 metres according to Google maps, 2 min by car and 7 min walk.

Crazy world we live in means close proximity to a Waitrose can add up to 10% on a house price

 

[pjgtech]

So this is where my little spray painting booth will live for now, in the corner of my garage....

 

[pjgtech]

Nuther stupid begionner question, I assume you realease the pressure once finished using the compressor, and don't just leave it pressurised?

And another, I've read that some compressors. hoses, air brushes, etc can have o rings that are affected by thinner, so do I need to be careful? I have just bought some mr surfacer leveller 400 thinner, will that be ok in my chosen choice of AB and compressor?

 

[Stefee]

I always drain the compressor at the end of a spraying session and leave the drain plug out just the same as a full size compressor in a spray shop.
Regarding lacquer thinners affecting rubber o rings and seals, this is a possibility but if you don't leave those parts soaking in thinners or leave thinners in the cup ( unless a suction feed model ) you shouldn't have a problem.
I would be very worried if thinners was in my compressor or hoses.

 

[pjgtech]

I'm all set up, but not going to use it today, been watching several "How to" vids on air brushing for beginners, eg: me!
Seems like I should start with a lowish pressure, around 15 to 20? and I should also start with thinned paint, either mix separately then pour in the AB bowl, or if adding straight to the bowl, add thinner/water first, then add the paint.
Can use gentle pressure on the AB to get backflow to mix the paint in the bowl as well.

Then forget about painting any models (for now) and just practice on paper/card.

Use appropriate trigger control, for a dual action AB...
Eg: trigger down for air, can vary downward pressure for air flow control (as well as compressor pressure control)
Trigger back for paint, can vary backward pressure for paint flow control.
Trigger forward to stop paint, but trigger still down.
Trigger up/off to stop air.
I am aware that keeping the air on helps to reduce/stop paint build up on the needle, etc.

Practice thin lines, thick lines, horizontal lines and vertical lines.
Try to avoid splatter and try to avoid spidering.
Practice dots, small dots, larger dots, etc. swirls, curves, moving the AB near the surface and further from the surface, etc.

Experiment with the AB to just try to get a "feel" for it.
One technique seemed to be to paint thin horizontal lines, then vertical lines to form a grid, quite small / thin, then try to get small dots into every grid section, and then again try to get small dots on the line intersections.

Make sure I know how the AB comes apart and goes back together, make sure I don't leave paint in the brush, clean it out after every use, etc.
Couple of YT vids have just suggested cleaning out with plain water, or is there better cleaners, I assume you can buy all manner of AB cleaning solutions, but I would imagine maybe they are just variations on Isopropol Alchohol?

Anything else I need to know for now?
Will probably be taking the plunge tomorrow, or if its really hot, (likely here 30+) may wait till Thursday....

 

[Tim Marlow]

Airbrushing is something that almost all modellers do slightly differently to the next guy. Despite this, we all get it to work.

The point of this comment is to say what a video tells you works for them may not work for you, so do not be scared to experiment.

From my perspective, I’ve never got on with water based acrylics through an airbrush. Tried dozens of times but just get frustrated. I therefore gave up and use Tamiya/Mr Color. However, others get really first class results using acrylic paint so it’s not the medium per se, just that it doesn’t work for me. Might be because I learned using enamels, so find organic solvent based paint more intuitive.

Practice, practice, practice, and when you experiment, only change one thing at a time. It’s the only approach that works .